Grater Exhaust Tip

Thanks for visiting our site!
Grater Exhaust Tip
Checkout Ebay Auctions For The Cheapest Prices

Check out Amazon:

Account limit of 2000 requests per hour exceeded.

Here are some more information for Grater Exhaust Tip:

Many of you add aftermarket coolers to your cars and this is always a good idea. Here are some hints.

1-Always mount the cooler in a place that has good air flow and if mounting in front of the radiator always make sure the fin's in the cooler are parallel with the fin's in the radiator to avoid restricting air flow to the radiator. If you must place the cooler in an area with little air flow a FAN is a must.

2-When Installing coolers make sure lines are clear of anything that can rub them and always use line that's approved for transmission/hydraulic fluid. Fuel line will not work and will break down in transmission fluid.

3-By passing the radiator is the way I prefer a cooler be set up. Generally the transmission will run cooler this way and additionally this may take some of the load off the radiators job of cooling the engine.

4-When hooking up multiple coolers several things should be noted. The cooler itself is a restriction of flow and this restriction while not a problem for the cooling or lube to the trans can cause excessive pressure inside the converter. This can force the converter against the flex plate more so than normal and cause wear to the engine thrust bearing. A stopped up or severely restricted cooler or cooler lines can do the same. So when installing more than one cooler its advised to put them in parallel with each other, This means one line from the trans is split with a Y and one line run to each cooler then out of each and into a Y back to a single line running to the trans. This will assure adequate cooling while reducing the wear to the engine thrust bearing. Always use line that's at least as large as the inlets in the cooler, Avoid extreme twist or turns in them particularly with rubber lines.

5-Type and brands of coolers; I really have no preference here as far as brand. From my experience and expensive brand name or a generic unit appear to do the same job. I have found the stacked plate (Flat tube) Types when measured inlet to outlet temp drop tend to be more efficient in the same dimensional sizes with a greater temperature drop. I did a test once with two coolers in parallel one round tube and one flat with a laser thermometer to determine this.

6-This is not specifically about a cooler but about cooling. Always be sure that the metal lines coming from the transmission under car do not contact the headers or exhaust. I once had a car where the transmission temps would sky rocket when the car was being run hard and couldn't understand why. I after some looking around found that the cooler lines in and out were pinned against the headers. This would super heat the fluid when the headers got hot. Moved them away and the problem was solved, So always keep trans cooler lines factory or otherwise as far away from the exhaust as possible.

7-Trans temps- This question gets ask a lot. What's TOO HOT? Well ideally you want you average temp to stay under 190 degrees however I would not get to concerned till the temps get at and or over 230 degrees. Heat can damage a trans but with the exception of extreme heat 250 or higher this damage is a long term killer by breaking down fluid and causing rubber seals to harden and break.

8-Never use your cooler lines to remove fluid from your transmission by starting the engine or in and attempt to flush by catching fluid in a pan while adding fluid to the dipstick. When this is done no lube is being sent to the planets and bushings and they can go dry and melt down very quickly destroying or significantly shortening the life of your transmission.

9-It is advisable to fully and properly flush a cooler especially when a converter failure is involved. Where a transmission internal failure is unlikely to put debris in the cooler since all fluid coming from transmission must travel through the trans filter. The fluid coming from the Pump or converter does not and any debris from these will certainly end up in the cooler. Its always a good idea to power flush a cooler or replace after a failure but is particularly important in the case of this type failure. Anything that's in your cooler or lines will end up in your Valve Body, Bushings and Planets. A cooler cannot be properly cleaned simply by blowing air through it. A can of cooler flush which most transmission shops and or transmission parts suppliers should have followed by a blow out with air is the correct way to do it.

10-When installing rubber cooler lines to metal lines it's a good idea to put a small flair at the end of the metal line. Not too big because you will tear the line on the inside during install. Then place a clamp just ahead of the flair. Also roughening up the outer surface of the metal line with very coarse sand paper in area where clamp will ride will help assure a good seal and reduce the possibility of blow off. Never over tighten clamps to the point of the rubber oozing through or being cut this will cause a failure too.

11-Temp sending units- The best place for these is in the pan since that will give the best average temperature which is what's important, using the pressure port is ok however you will show temps 10 to 20 degrees higher average than you would in the pan. I do not suggest placing temp senders in either the inlet or outlet from the cooler as they will increase cooler restriction and increase the odds of a leak.

For more information on High Performance Transmission please visit http://www.performabuilt.com/

Get Tips For The Right Holiday Travel Package

Well it is not usually wise to be traveling during holidays as these are the times when almost every other person in the world is traveling. It is of course best to plan ahead or book ahead and go to your destination early to avoid all the hassle but if you're one of those last minute people or probably one of those who can't really avoid it, you should follow the next few tips for a fairly better journey and maybe a cheaper stay.

- Holiday travel packages were never made with only one person in mind; no two people are alike, keep this in mind because the agencies that packed them have kept these in mind, use this fact to haggle your way into cheaper or sometimes better deals. Even if there are ready made packages, you can ask for extra perks especially if you're staying for more than a week.

- Be careful of travel agents. Travel agents may give you the best deal for your package, which normally include airfare, lodgings and transportation, but a really good agent can be really flexible. One example would be if you want a rental car for the first half of your trip but you want to get rid of it by the second half, a good agent can arrange this for you, sometimes for a cheaper price.

- Be sure that the package you want is available, you don't want to get pulled into something that ends up being sold out, some people give out too-good-to-be-true packages which end up being "sold out" in the end, so before you make a deal or transfer a morsel of cash, make sure that it is still available.

- Be sure to know exactly what airline and route your taking, you won't want those unpleasant layovers which can be a real pain, not to mention delay your schedule.

- A good sign of a good package is one that is very flexible, as said before, no two people are alike, and a good package should reflect that, it should allow you to choose between destinations, as well as brands and lodgings without changing the price. A choice in which rental car to take is also a sign of a good package.

- Finally, it's good to ask for discounts that you might get if you do certain stuff, like stay in the hotel for more than a week, or sign up on the internet instead of by phone. Research first before you cough up the money for down-payment; make sure you've exhausted all possible discount generating ways before you decide on a package.

About the Author

Trisna Ida website's: Non Woven Shopping Bags,
Shower Dispenser, And Rotary Cheese Graters.

Thanks for visiting!